DIY Pocket Wedding Invitations Part 2

In Part 1 we made the envelopes and part of the backing, this will show how to complete the invitation. I used Word to design my text and graphic inside of a 4" x 6" space and printed it. 

Tree graphic with 2 little birdies. 

I then cut them out and used my glue runner to adhere them to the flat part of the invitation.  I decided to move the glitter rectangle to go "inside"/behind the pocket, because I liked how it looked. 

Glitter paper in pocket. 

I also added a quote that I printed and then placed that on top of a rectangle of coordinating vellum, but let creativity be your guide, this was just what I chose. 

I also used word to type up my directions and RSVP. They directions were cut to 4" x 5.5", but anything under 5"x 7" will fit.  I cut the RSVP to 3.5" x 5.5" so that when they were stacked together they would later nicely.

Inserts in pocket. 

Now you're all done! The invitations here will fit inside A7 sized envelopes and the RSVP inserts will fit inside A2 sized envelopes.  Mine were .70 to mail each, and I also added a small Velcro closure for my invitations to give them a little, well, snap. :) Happy Crafting! 

2 Sticks and String

Why did you start knitting?  

It's a question I hear all the time and the truth is I started because I'd spent enough time wanting to learn and decided to spend time actually knitting.  It's one of the most rewarding things in the world to take 2 sticks and a length of string and turn it into something else.  The very nature of knitting is transformative, not just for the material used, but for the knitter as well.  It's difficult to explain to someone who has yet to cast on, it seems like a hassle to learn.  In the beginning there is such a knowledge gap that even a simple pattern looks coded gibberish, what is K2 P2 ribbing?  Let's not forget charts, they might as well be secret treasure maps, read in the opposite direction; it all seems terribly convoluted.  But if you can get past those first few weeks or months of confusion and frustration, there's a membership card with your name on it, you will become...a knitter! It sounds strange, but every time I knit in public or ship out an item to a customer, I'm always asked in amazement "What are you making?" Or "Did you make that?", usually followed by "I wish I could knit." What I'd like to say is you can! Today could be the last day that you wish you knew how to knit and tomorrow will be the first day you started knitting. I don't know a single knitter that dwells on the initial difficulty of learning, each one sort of forgets any of the problems in the beginning and instead tells you how wonderful it feels to knit, myself included.  I remember my first hat I made, it was horrid, but I made it! I was so proud.  I still have it so I don't forget how far I've come and to use as an example whenever someone says they might not be good at knitting.  

Ribbon Roses

These are a few roses that I made from organdy ribbon.  

These are simple to create, here's what you'll need: 

• Ribbon that you like (1-1/2 inches wide and 30 inches long)
• Stem wire 
• Needle and thread coordinating colors will be best, but any should work. 
• Wire cutters  
• Scissors
• Green satin fabric (1/2 inch wide by 6 inches long) 
• Fabric glue

Start by folding ribbon down at a 45 degree angle about 3" from one end. 

Then fold down the again forming a point. 

Continue using the long part as the "working" ribbon.

You'll form a "diamond".​

Continue like this until you have 4 layers of diamonds.​

Now you'll find a tiny hole in the center: 

Thread the end of the ribbon you were folding ("working" ribbon end) through the hole, gently, until there is enough to  grab, try not to pull too hard.  

Twist the end in a clockwise direction while gently holding the layers in the opposite hand and releasing them as the edges begin to twist. ​

When you reach the end grab the loose end and bunch it with the end you pulled through and sew them together with your needle and thread. 

Trim excess ribbon.​

Cut length of wire to about 5". 

Wrap wire around edge of fabric. 

Cover stitches with small piece of green fabric and glue, then you're done. 

Now you've made your first flower, make a bunch and turn them into pins or into a tiny garden! 😃